Rainwater Pumps
EBARA MULTIGO and EBARA IDROGO vertical multistage pumps are a high quality stainless-steel pump range used for domestic, agricultural and commercial water supply from wells & cistern tanks.
Installed as a submersible pump within the rainwater storage tank, the EBARA Multigo & EBARA Idrogo submersible rainwater pumps provide water supply to header-tank installations (indirect gravity-based systems) as well as to direct-pressurised applications.
Multigo
The EBARA Multigo pump is equipped with a 1¼“(FT) pump in-take in order to connect a floating suction filter to extract rainwater from the middle part of the rainwater column, where the cleanest water lies.
Idrogo
The EBARA Idrogo pump is equipped with a stainless-steel sieve in-take for clear water with solids up to 2.5mm in diameter.
Both the Multigo & Idrogo rainwater pumps have a 1¼“(FT) pump discharge.
An (external) non-return valve on the pump discharge or discharge pipe within the rainwater tank is to be included during installation to prevent a backflow of water after the pumping cycle has ceased.
Centrifugal Suction Pumps
Self-priming centrifugal suction pumps such as the EBARA JES-JE & EBARA JESX-JEX are located in close proximity to but outside of the rainwater tank.
Rainwater Pump Operation
For automatic pressurised water supply and dry-run protection an additional external Pressure Switch / Pump Controller is required.
Pump motor-protection is included when operating the pump via a Control Panel.
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 400V|3Ph|50Hz| P1= 0.95kW| P2= 0.60kW| I=1.9A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 48.0 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 400V|3Ph|50Hz| P1= 1.18kW| P2= 0.75kW| I=2.2A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 60.0 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 400V|3Ph|50Hz| P1= 1.33kW| P2= 0.90kW| I=2.4A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 72.0 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 400V|3Ph|50Hz| P1= 1.55kW| P2= 1.10kW| I=3.0A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 84.0 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 400V|3Ph|50Hz| P1= 1.22kW| P2= 0.90kW| I=2.3A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 49.0 m | Q(max)=7.2 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 400V|3Ph|50Hz| P1= 1.52kW| P2= 1.10kW| I=3.1A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 62.0 m | Q(max)=7.2 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 400V|3Ph|50Hz| P1= 1.90kW| P2= 1.50kW| I=3.5A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 74.0 m | Q(max)=7.2 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 0.82kW| P2= 0.44kW| I=3.8A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 36.5 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 0.82kW| P2= 0.44kW| I=3.8A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C Dry-Run protective operation via Float-Switch Pump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 36.5 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 1.00kW| P2= 0.60kW| I=4.3A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 48.0 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 1.00kW| P2= 0.60kW| I=4.3A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C Dry-Run protective operation via Float-Switch Pump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 48.0 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 1.25kW| P2= 0.75kW| I=5.7A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 60.0 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 1.25kW| P2= 0.75kW| I=5.7A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C Dry-Run protective operation via Float-Switch Pump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 60.0 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 1.42kW| P2= 0.90kW| I=6.8A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 72.0 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 1.42kW| P2= 0.90kW| I=6.8A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C Dry-Run protective operation via Float-Switch Pump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 72.0 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 1.60kW| P2= 1.10kW| I=7.3A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 84.0 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 1.60kW| P2= 1.10kW| I=7.3A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C Dry-Run protective operation via Float-Switch Pump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 84.0 m | Q(max)=4.8 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 1.33kW| P2= 0.90kW| I=6.4A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 49.0 m | Q(max)=7.2 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 1.33kW| P2= 0.90kW| I=6.4A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C Dry-Run protective operation via Float-Switch Pump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 49.0 m | Q(max)=7.2 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 1.62kW| P2= 1.10kW| I=7.5A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C without automatic level controlPump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 62.0 m | Q(max)=7.2 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
5"-Vertical multistage submersible pressure pump in stainless-steel for clean water with 20m cable 230V|1Ph|50Hz| P1= 1.62kW| P2= 1.10kW| I=7.5A for pressurised water-supply from wells, cistern tanks & rainwater harvesting tanks Fully submerged or partially submerged operation| IP 68 Insulation-Class: F | 2-pole T(max)=40°C Dry-Run protective operation via Float-Switch Pump body, casing cover in stainless steel (CrNi-Steel 1.4301) External casing & motor casing in stainless steel (CrNi-steel 1.4301) Double mechanical seal (carbon/ceramic/NBR) with interpoised oil-chamber Impeller & diffuser in technopolymer Discharge outlet: 1¼“ (FT) Sieve intake | Solids passage: 2.5 mmH(max)= 62.0 m | Q(max)=7.2 m³/h Submergence(max)=17 m WRAS-approved | TÜV/GS-certified | CE-certified | WEEE-vertified Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
Self-priming single-impeller centrifugal pump in stainless steel (AISI 304) for water supply, pressure boosting, irrigation and rainwater harvesting400V|3Ph|50Hz| P1=0.97kW | P2=0.60kW | I=1.9 A | 2-pole Insulation class: F | Protection Degree: IP44 - low noise operation - with fan-cover and motor-support Pump Body (AISI 304) & Shaft (AISI 303) in stainless steel Impeller in stainless steel (AISI 304) Service-free mechanical seal (Carbon/Ceramic/NBR) O-Rings in NBR External motor-protection provided on-site Motor Bracket in stainless steel (AISI 304) Ejector/Diffuser in PPE+PS (reinforced) T(max): 45°C Suction Intake: 1¼“ (FT) Discharge: 1" (FT) H(max) = 41.0 m | Q(max) = 4.2 m³/hSuction height (max.): 6 m CE | WEEE | Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
Self-priming single-impeller centrifugal pump in stainless steel (AISI 304) for water supply, pressure boosting, irrigation and rainwater harvesting400V|3Ph|50Hz| P1=1.15kW | P2=0.88kW | I=2.1 A | 2-poleInsulation class: F | Protection Degree: IP44 - low noise operation - with fan-cover and motor-support Pump Body (AISI 304) & Shaft (AISI 303) in stainless steel Impeller in stainless steel (AISI 304)Service-free mechanical seal (Carbon/Ceramic/NBR) O-Rings in NBR External motor-protection provided on-site Motor Bracket in stainless steel (AISI 304) Ejector/Diffuser in PPE+PS (reinforced) T(max): 45°C Suction Intake: 1¼“ (FT) Discharge: 1" (FT) H(max) = 50.0 m | Q(max) = 4.2 m³/hSuction height (max.): 6 m CE | WEEE | Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com
Self-priming single-impeller centrifugal pump in stainless steel (AISI 304) for water supply, pressure boosting, irrigation and rainwater harvesting400V|3Ph|50Hz| P1=1.77kW | P2=1.10kW | I=3.3 A | 2-poleInsulation class: F | Protection Degree: IP44 - low noise operation - with fan-cover and motor-support Pump Body (AISI 304) & Shaft (AISI 303) in stainless steel Impeller in stainless steel (AISI 304)Service-free mechanical seal (Carbon/Ceramic/NBR) O-Rings in NBR External motor-protection provided on-site Motor Bracket in stainless steel (AISI 304) Ejector/Diffuser in PPE+PS (reinforced) T(max): 45°C Suction Intake: 1¼“ (FT) Discharge: 1" (FT) H(max) = 59.0 m | Q(max) = 4.5 m³/hSuction height (max.): 6 m CE | WEEE | Made in EU Manufacturer: EBARA Pumps Europe S.p.A., Via Torri di Confine 2/1 int. C, 36053 Gambellara (Vicenza), Italy Phone: +39 0444 706811Email: ebara_pumps@ebaraeurope.comWeb: www.ebaraeurope.com